Skip to content

Releases

V2.6.0

Choose a tag to compare

@mews-se mews-se released this 13 Nov 15:53

There are two builds now. TPFanControl.exe is 64-bit and TPFanControl-x86.exe is 32-bit. Take the 64-bit one unless you run 32-bit Windows or need TVicPort, since TVicPort.dll only exists as a 32-bit dll. Copying the new TPFanControl.exe over an existing install moves it to 64-bit. To stay on x86, rename TPFanControl-x86.exe to TPFanControl.exe before you copy it in, so the service and the Startup shortcut keep pointing at the same file. Close the tray and stop the service first either way.

Smart mode now leaves the fan to the BIOS while no sensor gives a sane reading, instead of taking 0 °C at face value. Some ECs answer with zeros for a while after a resume, and that used to put the fan at the bottom of the curve.

The mode that was active before a lid close, a sleep or a Modern Standby period now comes back once two sane readings are in, without the long sleeps that used to stall the program. PowerSuspendMode=1 no longer ends up stuck in BIOS mode after sleeping with the lid closed.

The step from level 7 to 64 used to wait for 4000 rpm. It now also happens once the rpm stops rising, so machines where level 7 tops out lower, or that report no rpm at all, reach full speed too.

Thanks to mwietrzy, whose PR #1 from an X395 turned up the resume problems and the 4000 rpm limit.

LpcACPIEC.bin is unchanged, the signed module from PawnIO.Modules 0.2.10 (LGPL-2.1).

V2.5.1

Choose a tag to compare

@mews-se mews-se released this 26 Aug 16:19

Start with Windows now manages a shortcut in the user's Startup folder instead of a run key entry. Windows 11 was seen silently skipping the run entry at logon — value present and enabled, nothing in the event logs about why — while a Startup folder shortcut is not skipped. Flipping the toggle in either direction also cleans up a leftover run entry from earlier versions, and enabling it now starts the service right away instead of leaving the fan with the BIOS until the next boot.

No changes to the fan logic or the PawnIO port backend from 2.5.0; LpcACPIEC.bin still goes next to the exe.

V2.5.0

Choose a tag to compare

@mews-se mews-se released this 26 Aug 15:28

Fan control now works with memory integrity (HVCI) enabled, which is where the TVicPort driver is refused on current Windows 11 installs.

The EC is reached through a switchable port backend. PawnIO is tried first: install the WHQL-signed driver from pawnio.eu (or winget install namazso.PawnIO) and keep LpcACPIEC.bin from this release next to the exe. TVicPort remains as a fallback for systems without memory integrity, now loaded dynamically — the exe no longer refuses to start when TVicPort.dll is missing.

Details:

  • PawnIO is spoken to directly over its device io control interface, so the 32-bit exe works against the 64-bit driver without PawnIOLib
  • the signed LpcACPIEC module reaches the EC through the classic ports 0x62/0x66; the port layout probing skips 0x1600/0x1604 on that backend
  • the engine starts the demand-start PawnIO driver service itself when needed
  • new ini key PortBackend= (auto, pawnio, tvicport)
  • UseTWR needs TVicPort and now says so in the log instead of timing out

LpcACPIEC.bin is the unmodified signed module from PawnIO.Modules release 0.2.10, LGPL-2.1.

V2.4.0

Choose a tag to compare

@mews-se mews-se released this 26 Aug 13:44

First release of the continuation fork, carrying on where FanDjango's V2.3.23 left off.

  • Fixed the crash that killed a tray client on its first data cycle
  • The engine log is mirrored into client windows, engine timestamps intact
  • The tray menu no longer competes with the engine for the EC mutex
  • ErraticSensorGuard: a sensor that keeps jumping between the same two values is quarantined and no longer drives the fan
  • LidSmartLevel: run a second smart profile while the lid is closed, for docked use
  • Emergency level 64 spins up through level 7 before disengaging, in smart and manual mode alike - on newer ECs the disengaged ramp is a crawl, so this cuts the time to full airflow from a near idle fan
  • Level 64 shows as 64 in the window instead of 0
  • The version resource finally moved on from 1.0.0.63

Install and configuration notes are in the README. Verified on a ThinkPad X13 Gen 3; the fixes are model independent.

V2.3.23

Choose a tag to compare

@mews-se mews-se released this 26 Aug 07:57

Note: This is to be considered "experimental", as there has already been one report of this release not working correctly, so only try this if you are feeling adventurous and want to help testing this.

Current status: See issue #18 and anyone wanting to add reports, use that issue please.

One user reports: This does not work on this system:
ThinkPad P15 Gen 2
Windows 10 22H2, build 19045.6456

"Start with Windows"

Thanks to some very hard work by @mackid1993, here is a new release that you should try out - and I would appreciate feedback, not only if it does not work, but especially if it does work for you. Please please include the operating system version and laptop type.

What is new?

The change involves the way TPFanCtrl2 is started (if it is not started manually). Up to now, you needed some special ideas to make it start automatically after windows startup.

This new release incorporates a number of changes to make this startup easier - simply activate the "Start with Windows" option when right-clicking the taskbar icon. You should deactivate the previous methods that you have been using to start TPFanCtrl2 automatically on windows startup.

Check out README.md, "running at startup".

So:

New way to start TPFanCtrl2 at windows startup

*) Feedback, please

V2.3.22

Choose a tag to compare

@mews-se mews-se released this 26 Aug 07:56

Some more UI tweaks by @Ew687

V2.3.21

Choose a tag to compare

@mews-se mews-se released this 26 Aug 07:56

Add "0x40" and "0x80" to manual speed drop down control

image

Release bumped to V2.3.21, source branch: "2.3.21" in this repo

Confirmed support for: P53, Z13, Z16 Gen 1, Z16 Gen 2, P16 Gen1 AMD, T16 Gen1 AMD, X1 carbon gen12, X230T, P1 Gen7

V2.3.20

Choose a tag to compare

@mews-se mews-se released this 26 Aug 07:56

Revert EC speed setting optimisation due to reported problems/regression on P15 Gen 2

V2.3.17

Choose a tag to compare

@mews-se mews-se released this 26 Aug 07:55

Maintenance - finalizing changes to temperature display (ListView fourth collumn (EC Offset))

  • Final changes to temperature display (Added fourth collumn to temperature listview (EC Offset)) (Thanks: @en1003QwQ)
image

The coloring of the temperatures and the collumn title corresponds to the .ini file settings of "IconLevels"

Release bumped to V2.3.17, source branch: "2.3.17" in this repo

Confirmed support for: P53, Z13, Z16 Gen 1, Z16 Gen 2, P16 Gen1 AMD, T16 Gen1 AMD, X1 carbon gen12, X230T, P1 Gen7, ThinkPad P16 Gen 3, ThinkPad P15 Gen 2(*)

(*) Currently under investigation

@en1003QwQ has also contributed chinese comments to the sample .ini file, which now contains English, German and Chinese.

You can find the ini file in the repo download or here and as an asset of this release.

V2.3.16

Choose a tag to compare

@mews-se mews-se released this 26 Aug 07:56

Maintenance - finalizing changes to temperature display (ListView in color)

  • Final changes to temperature display (ListView in color) (Thanks: @en1003QwQ)
image

The coloring of the temperatures and the collumn title corresponds to the .ini file settings of "IconLevels"

Release bumped to V2.3.16, source branch: "2.3.16" in this repo

Confirmed support for: P53, Z13, Z16 Gen 1, Z16 Gen 2, P16 Gen1 AMD, T16 Gen1 AMD, X1 carbon gen12, X230T, P1 Gen7