Issues with esp32

[Lor3wp]

Hi!

I have been figting for couple of days with this propblem. I get the rainbow_v2 and led strip light up but I cannot by any mean connect to esp32 from hyperion. Im setting static ip in ConfigStatic and putting same ip and udp port in config file for hyperion and in updraw led output setting. I get no reaction and i have no clue how to begin debugging here.

Thanks: P

[SciLor]

Please check the UART Output for the log.

[Lor3wp]

Hi! Is that in the hyperion settings or arduino ide? I did uncommented the loglevels in ConfigStatic.h but only thing its logging is D: HEAP=244308.

[SciLor]

You should get several log messages when you boot your esp32 via UART (Visible in the Serial Monitor of Arduino).
The heap log comes every X seconds. But there should be more, before that.

[Lor3wp]

Oh i see i did get them!
I: Start logging I: CFG=Static config loaded D: Chipset=Clockless, dataPin=17, clockPin=NONE, colorOrder=10, ledCount=50 I: Reset Mode D: Interval set to 500ms D: WrapperWiFi(ssid="ssid", password="password") I: Connecting to WiFi I: Using static ip I: Connected successfully, IP address: 192.168.0.9 I: Prepare OTA D: WrapperOTA(hostname="HyperionRGB") I: OTA Ready I: Open port 19446 for UDP with protocol 0... I: success I: Open port 19444 for TCP...

I didnt see anthing wrong here so i didnt give it a second tought. (the ssid and password are correctly i just changed them here) I set the static ip and udp port in hyperion config file. Only thing is that i dont see the name of the device in my router settings when checking for connected devices. It was STATIC IP ADDRESS at some point but now it dissapeard .

[Lor3wp]

I found in hyperion log this message, I feel like that could be the issue.

2024-02-18T11:04:39.676Z [LEDDEVICE] (ERROR) Dummy device type (file) used, because configured device 'udp' throws error 'unknown device'

[Lor3wp]

Hi! I am still not able to figure out what is the issue, would you have any suggestions to try out? The esp32 manages to control led strip but i have no clue what to do with hyperion.

[SciLor]

Sorry, I cannot support Hyperion here. I would suggest getting onto the Hyperion forum for that.
Please check if IP / Port / Protocol are okay in Hyperion ng.

[Lor3wp]

I see i will try to hop on there, couple thing from this repo. I uncommented #define CONFIG_ENABLE_WEBCONFIG 0 and set it to 0 and now i got new stuff in the serial monitor.

`ets Jul 29 2019 12:21:46

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1184
load:0x40078000,len:13260
load:0x40080400,len:3028
entry 0x400805e4
I: Start logging
I: CFG=loadStaticConfig initConfig
I: Configuration read at 0x0 with v3
V: CFG=ip2cfg: 192.168.0.100
V: CFG=ip2cfg: 255.255.255.0
V: CFG=ip2cfg: 192.168.0.1
I: Configuration saved at 0x0 with v3
I: CFG=loadStaticConfig END
I: Configuration read at 0x0 with v3
V: CFG=cfg2ip: 192.168.0.100
V: CFG=cfg2ip: 255.255.255.0
V: CFG=cfg2ip: 192.168.0.1
I: CFG=EEPROM config loaded
D: CFG Show Config
D: +WIFI+
D: ssid=c4e32c
D: password=283474840
D: ip=192.168.0.100
D: subnet=255.255.255.0
D: dns=192.168.0.1
D: hostname=HyperionRGB
D: +LED+ idleMode=1
D: timeoutMs=5000
D: autoswitch=1
D: count=10
D: static-color.r=254
D: static-color.g=254
D: static-color.b=254
D: +PORTS+
D: jsonServer=19444
D: udpLed=19446
D: +MISC+
D: udpProtocol=0
D: Chipset=Clockless, dataPin=17, clockPin=NONE, colorOrder=10, ledCount=10
I: Reset Mode
I: Mode changed to 1
D: WrapperWiFi(ssid="c4e32c", password="283474840")
I: Connecting to WiFi c4e32c
I: Using static ip
I: Connected successfully, IP address: 192.168.0.100
I: Prepare OTA
D: WrapperOTA(hostname="HyperionRGB")
I: OTA Ready
I: Open port 19446 for UDP with protocol 0...
I: success
I: Open port 19444 for TCP...
I: HEAP=239156`

wich is nice cus im getting a bit more stuff from here. But im confused by this line D: Chipset=Clockless, dataPin=17, clockPin=NONE, colorOrder=10, ledCount=10
why is the colorOrger 10? it is set to RGB in configStatic.h dose this have anything to do with anything? Heres my ConfigStatic.h if it will help at all.
`/------------------------------------------------/
/Configuration type/

#define CONFIG_ENABLE_WEBCONFIG 0

//Replaces all values in the webconfig with the ConfigStatic.h values when CONFIG_ENABLE_WEBCONFIG is enabled
#define CONFIG_OVERWRITE_WEBCONFIG 1

/------------------------------------------------/
/Logging level/

#define LOGLEVEL LOG_LEVEL_INFOS
#define LOGLEVEL LOG_LEVEL_DEBUG
#define LOGLEVEL LOG_LEVEL_VERBOSE

/------------------------------------------------/
/Main static configuration/
//This cannot be changed via web inteface

// #define CONFIG_LED_SPI_CHIPSET WS2801 //Comment out for clockless
#define CONFIG_LED_CLOCKLESS_CHIPSET WS2812 //Comment in for clockless
//#define FASTLED_ALLOW_INTERRUPTS 0 //Comment in if clockless stripe (ex. WS2812B) is flickering
//#define CONFIG_LED_PWM 1 //Comment in if PWM Stripe

#define CONFIG_LED_DATAPIN 17 //Comment out for PWM
// #define CONFIG_LED_CLOCKPIN D2 //Comment out for clockless / PWM
//#define CONFIG_LED_PWM_RED D1 //Comment in for PWM
//#define CONFIG_LED_PWM_GREEN D2 //Comment in for PWM
//#define CONFIG_LED_PWM_BLUE D3 //Comment in for PWM

//Pin order, see FastLED doc. NodeMCU should work with FASTLED_ESP8266_RAW_PIN_ORDER
#define FASTLED_ESP8266_RAW_PIN_ORDER
//#define FASTLED_ESP8266_NODEMCU_PIN_ORDER
//#define FASTLED_ESP8266_D1_PIN_ORDER

#define CONFIG_LED_COLOR_ORDER RGB
#define CONFIG_LED_COUNT 10

//OFF, HYPERION_UDP, STATIC_COLOR, RAINBOW, FIRE2012, RAINBOW_V2, RAINBOW_FULL
#define CONFIG_LED_STANDARD_MODE HYPERION_UDP
#define CONFIG_LED_HYPERION_AUTOSWITCH true
#define CONFIG_LED_STANDARD_MODE_TIMEOUT_MS 5000
#define CONFIG_LED_STATIC_COLOR CRGB(254, 254, 254)

/------------------------------------------------/
/Main configuration/
//You can leave it empty and override it via the web interface on port 80
#define CONFIG_WIFI_SSID "c4e32c"
#define CONFIG_WIFI_PASSWORD "283474840"

#define CONFIG_WIFI_STATIC_IP 1
const byte CONFIG_WIFI_IP[] = {192, 168, 0, 100};
const byte CONFIG_WIFI_SUBNET[] = {255, 255, 255, 0};
const byte CONFIG_WIFI_DNS[] = {192, 168, 0, 1};

#define CONFIG_WIFI_HOSTNAME "HyperionRGB"

#define CONFIG_PORT_JSON_SERVER 19444
#define CONFIG_PORT_UDP_LED 19446

#define CONFIG_PROTOCOL_UDP UDP_RAW //UDP_RAW, UDP_FRAGMENT, UDP_TPM2 - Hyperion 0: RAW, 2: Fragmented, 3: TPM2 - Check the README

#define CONFIG_OTA_AP_PASSWORD "HyperionRGB"
`

[SciLor]

Then you should check the library versions you use so they are the same as mentioned in the readme. Otherwise there may be problems.